BT35-11防爆（防腐）軸流通風機【BT35-11防爆（防腐）軸流通風機】=======BT35-11防爆（防腐）軸流通風機【BT35-11防爆（防腐）軸流通風機】=====

一、=BT35-11防爆（防腐）軸流通風機【適用范圍

1. 爆炸性氣體環境危險場所：1區、2區；
2. 可燃性氣體、蒸氣級別：ⅡA、ⅡB；
3. 溫度組別：T1~T4。
1. For the dangerous sites with explosive air mixture: 
1 division、2 division;
2. Flammable gas, steam class：ⅡA、ⅡB
3. Temperatures classification：T1~T4.

二、=BT35-11防爆（防腐）軸流通風機【安裝說明
 
1、安裝前應詳細檢查通風機是否因包裝運輸損壞變形，如有損壞，待修理妥善后，方可進行安裝
2、安裝時要注意檢查各連接部分有無松動，葉片與風筒間隙應均勻，不得相碰。
3、連接出風口的管重量不應由風機的風筒隨，安裝時應另加支撐
4、在通風機進風口端必須裝集風器，希望裝置防護鐵絲網。
5、風機底座必須與地基平面自然接合，不得敲打底座強制連接，以防底座變形，安裝時應校下機座，加墊鐵片，基本保持水平位置，然后擰緊地腳螺釘
6、、安裝完畢后，必須*行試驗，待運行正常后，才允許使用。
 
1, installed before the fan should be inspected in detail the damage caused by the deformation of transport packaging and, if damaged, to be properly repaired before they are allowed to install it. 

2, the installation should pay attention to check whether some of the loose connection, hairdryer blade gap should be uniform and may not encounter. 

3, the tube connecting the air blower should not be borne by the weight of the hairdryer with the installation of additional support should be. 

4, the fan must be installed into the air-side set the wind, and hope that wire protective devices. 

5, fan base must be the foundation of natural bonding plane, shall not be forced to connect the base hit to prevent deformation of the base, the installation should be under the base school, plus Sizing Block films, to maintain the level of the basic position, and then tighten the screw in the foot. 

6, After installation, it must first conduct a test, to be functioning properly before allowing the use of.

三、=BT35-11防爆（防腐）軸流通風機【

============