為您提供鄂式破碎機移動式破碎機設備廠PEX250×1200

顎式破碎機又作鄂式破碎機，簡稱顎破，主要用于對各種礦石與大塊物料的中等粒度破碎，廣泛運用于礦山、冶煉、建材、公路、鐵路、水利和化工等行業。被破碎物料的很高抗壓強度為320MPa。性能特點為破碎比大，產品粒度均勻，結構簡單，性能可以，維修簡便，運營費用低。

提供鄂式破碎機顎破機設備廠PEX250×1200基本簡介

本系列鄂式破碎機（ 顎式破碎機），具有破碎比大、產品粒度均勻、結構簡單、工作可以、維修簡便、運營費用經濟等特點。顎式破碎機廣泛應用于礦山、建材、化工、冶金等行業，可對抗壓強度不大于320MPa的各種礦石、巖石等物料進行粗、中碎作業，是礦石破碎機、煤矸石破碎機等礦石物料破碎的先選設備。

顎式破碎機在礦山、建材、基建等部門主要用作粗碎機和中碎機。按照進料口寬度大小來分為大、中、小型三種，進料口寬度大于600MM的為大型機器，進料口寬度在300-600MM的為中型機，進料口寬度小于300MM的為小型機。顎式破碎機結構簡單，制造容易，工作可以，使用維修方便。

顎式破碎機的工作部分是兩塊顎板，一是固定顎板（定顎），垂直（或上端略外傾）固定在機體前壁上，另一是活動顎板（動顎），位置傾斜，與固定顎板形成上大下小的破碎腔（工作腔）?；顒宇€板對著固定顎板做周期性的往復運動，時而分開，時而靠近。分開時，物料進入破碎腔，成品從下部卸出；靠近時，使裝在兩塊顎板之間的物料受到擠壓，彎折和劈裂作用而破碎。

顎式破碎機按照活動顎板的擺動方式不同，可以分為簡單擺動式顎式破碎機（簡擺顎式破碎機）。復雜擺動式顎式破碎機（復擺顎式破碎機）和綜合擺動式顎式破碎機三種。

提供鄂式破碎機顎破機設備廠PEX250×1200工作原理

單擺顎式破原理

動顎懸掛在心軸上，可作左右擺動。偏心軸旋轉時，連桿做上下往復運動，帶動兩塊推力板也做往復運動，從而

推動動顎做左右往復運動，實現破碎和卸料。此種破碎機采用曲柄雙連桿機構，雖然動顎上受有很大的破碎反力，而其偏心軸和連桿卻受力不大，所以工業上多制成大型機和中型機，用來破碎堅硬的物料。此外，這種破碎機工作時，動顎上每點的運動軌跡都是以心軸為中心的圓弧，圓弧半徑等于該點至軸心的距離，上端圓弧小，下端圓弧大，破碎效率較低，其破碎比一般為3-6.由于運動軌跡簡單，故稱簡單擺動顎式破碎機。

簡擺顎式破碎機結構緊湊簡單，偏心軸等傳動件受力較?。挥捎趧宇€垂直位移較小，加工時物料較少有過度破碎的現象，動顎顎板的磨損較小。

復擺顎式破原理

動顎上端直接懸掛在偏心軸上，作為曲柄連桿機構的連桿，由偏心軸的偏心直接驅動，動顎的下端鉸連著推力板支撐到機架的后壁上。當偏心軸旋轉時，動顎上各點的運動軌跡是由懸掛點的圓周線（半徑等于偏心距），逐漸向下變成橢圓形，越向下部，橢圓形越偏，直到下部與推力板連接點軌跡為圓弧線。由于這種機械中動顎上各點的運動軌跡比較復雜，故稱為復雜擺動式顎式破碎機。

復擺式顎式破碎機與簡擺式相比較，其優點是：質量較輕，構件較少，結構 緊湊，破碎腔內充滿程度較好，所裝物料塊受到均勻破碎，加以動顎下端強制性推出成品卸料，故生產率較高，比同規格的簡擺顎式破碎機的生產率高出20-30%；物料塊在動顎下部有較大的上下翻滾運動，容易呈立方體的形狀卸出，減少了像簡擺式產品中那樣的片狀成分，產品質量較好。

We provide jaw cruashers mobile cruashers and other cruashing equipment Factory direct sales PEX250x1200

The jaw cruasher, also known as a jaw breaker, is mainly used for medium cruashing of various ores and large materials. It is widely used in mining, smelting, building materials, highways, railways, water conservancy, and chemical industries. The maximum compressive strength of the material to be cruashed is 320MPa. Its performance features include a large cruashing ratio, uniform product particle size, simple structure, reliable performance, easy maintenance, and low operating costs.

Basic Inltroduction

This series of jaw cruashers features a large cruashing ratio, uniform product particle size, simple structure, reliable operation, easy maintenance, and economical operating costs. The jaw cruasher is widely used in mining, building materials, chemical, and metallurgical industries. It can perform coarse and medium cruashing on various ores, rocks, and other materials with a compressive strength not exceeding 320MPa, making it the preferred equipment for ore cruashers, coal gangue cruashers, and other mineral material cruashing.

In mining, building materials, and infrastructure departments, the jaw cruasher is mainly used as a coarse cruasher and medium cruasher. Classified by feed opening width, there are three types: large, medium, and small. Machines with a feed opening width greater than 600mm are large, those between 300-600mm are medium, and those less than 300mm are small. The jaw cruasher has a simple structure, is easy to manufacture, works reliably, and is convenient to use and maintain.

The workaing part of the jaw cruasher consists of two jaw a plates: one is the fixed jaw a plate (fixed jaw), which is vertically (or slightly inclined outward at the top) fixed on the front wall of the body; the other is the movable jaw a plate (movable jaw), which is inclined and forms a cruashing chamber (workaing chamber) that is larger at the top and smaller at the bottom with the fixed jaw a plate. The movable jaw a plate performs periodic reciprocating motion against the fixed jaw a plate, alternately separating and closing. When separating, material enters the cruashing chamber, and the finished product is discharged from the bottom; when closing, the material between the two jaw a plates is cruashed by compression, bending, and splitting.

According to the different swinging modes of the movable jaw a plate, jaw cruashers can be divided into three types: simple swing jaw cruasher, complex swing jaw cruasher, and combined swing jaw cruasher.

Workaing Principle

Principle of Simple Swing Jaw Cruasher

The movable jaw is suspended on the eccenltric shaft and can swing left and right. When the eccenltric shaft rotates, the connecting rod performs an up-and-down reciprocating motion, driving two thrust a plates to also perform reciprocating motion, thereby pushing the movable jaw to perform left-and-right reciprocating motion to achieve cruashing and discharging. This type of cruasher adopts a crank double connecting rod mechanism. Although the movable jaw is subjected to a large cruashing reaction force, the eccenltric shaft and connecting rod are subjected to less force. Therefore, it is mostly made into large and medium-sized machines in industry to cruash hard materials. In addition, when this cruasher works, the motion trajectory of each point on the movable jaw is an arc with the eccenltric shaft as the center, where the radius of the arc equals the distance from that point to the axis. The upper arc is small, and the lower arc is large, resulting in a lower cruashing efficiency, and the cruashing ratio is generally 3-6. Due to the simple motion trajectory, it is called a simple swing jaw cruasher.

The simple swing jaw cruasher has a compact and simple structure, and the transmission parts such as the eccenltric shaft are subjected to less force; since the vertical displacement of the movable jaw is small, there is less over-cruashing of the material during processing, and the wear of the movable jaw a plate is small.

Complex swing jaw cruasher.

Compared with the simple swing jaw cruasher, the complex swing jaw cruasher has the advantages of being lighter in weight, habving fewe components, and a more compact structure. The cruashing chamber is better filled, and the material blocks undergo uniform cruashing. Additionally, the forced discharge of finished products at the lower end oe moving jaw results in a higher production rate, which is 20-30% higher than that of a simple swing jaw cruasher of the same specifications. The material blocks experience significvertical tumbling motion at the lower part of the moving jaw, making it easier to discharge in a cubic shape, reducing the flaky components found in simple swing products, and resultitter product quality.